cisco-sa-20190306-nxos-npv-dos
Vulnerability from csaf_cisco
Published
2019-03-06 16:00
Modified
2019-03-06 16:00
Summary
Cisco Nexus 9000 Series Switches Standalone NX-OS Mode Fibre Channel over Ethernet NPV Denial of Service Vulnerability

Notes

Summary
A vulnerability in the Fibre Channel over Ethernet (FCoE) N-port Virtualization (NPV) protocol implementation in Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. The vulnerability is due to an incorrect processing of FCoE packets when the fcoe-npv feature is uninstalled. An attacker could exploit this vulnerability by sending a stream of FCoE frames from an adjacent host to an affected device. An exploit could allow the attacker to cause packet amplification to occur, resulting in the saturation of interfaces and a DoS condition. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link: https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos ["https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos"] This advisory is part of the March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication, which includes 25 Cisco Security Advisories that describe 26 vulnerabilities. For a complete list of the advisories and links to them, see Cisco Event Response: March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication ["https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757"].
Vulnerable Products
This vulnerability affects the following Cisco products if they are running a vulnerable release of Cisco NX-OS Software: Nexus 9000 Series Switches in standalone NX-OS mode Only the following Nexus 9000 Series PIDs are vulnerable: N9K-C92160YC-X N9K-C9272Q N9K-C9236C N9K-C93180YC-EX N9K-X9732C-EX N9K-C93180LC-EX N9K-C93180YC-FX N9K-X9736C-FX To view the PIDs of the system, use the show inventory CLI command: 9K-A# show inventory NAME: "Chassis", DESCR: "Nexus9000 C93128TX Chassis" PID: N9K-C93128TX , VID: V02 , SN: SAL1822TF13 NAME: "Slot 1", DESCR: "1/10G-T Ethernet Module" PID: N9K-C93128TX , VID: V02 , SN: SAL1822TF13 NAME: "Slot 2", DESCR: "40G Ethernet Expansion Module" PID: N9K-M12PQ , VID: V01 , SN: SAL1910AMHD Note: For this vulnerability to occur, all of the following conditions must be met: The affected devices are configured as vPC peer switches. The fcoe-npv feature must be uninstalled. See Details ["#det"] for more information. For information about which Cisco NX-OS Software releases are vulnerable, see the Fixed Software ["#fs"] section of this advisory. Determining the Cisco NX-OS Software Release Administrators can check the release of Cisco NX-OS Software that is running on a device by using the show version command in the device CLI. The following example shows the output of this command on a device that is running Cisco NX-OS Software Release 7.0(3)I5(1): nxos-switch# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2016, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 07.57 NXOS: version 7.0(3)I5(1) [build 7.0(3)I5(0.9)] BIOS compile time: 06/29/2016 NXOS image file is: bootflash:///nxos.7.0.3.I5.0.9.bin NXOS compile time: 8/1/2016 23:00:00 [08/02/2016 00:30:32] . . .
Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products ["#vp"] section of this advisory are known to be affected by this vulnerability. Cisco has confirmed that this vulnerability does not affect the following Cisco products: Firepower 2100 Series Firepower 4100 Series Next-Generation Firewall Firepower 9300 Security Appliance MDS 9000 Series Multilayer Switches Nexus 1000V Switch for Microsoft Hyper-V Nexus 1000V Switch for VMware vSphere Nexus 2000 Series Fabric Extenders Nexus 3000 Series Switches Nexus 3500 Platform Switches Nexus 3600 Platform Switches Nexus 5500 Platform Switches Nexus 5600 Platform Switches Nexus 6000 Series Switches Nexus 7000 Series Switches Nexus 7700 Series Switches Nexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) mode Nexus 9500 R-Series Line Cards and Fabric Modules UCS 6200 Series Fabric Interconnects UCS 6300 Series Fabric Interconnects UCS 6400 Series Fabric Interconnects
Details
The affected devices are vulnerable when configured as outlined in the Vulnerable Products ["#vp"] section. The following commands will help identify these conditions: To verify the status of a vPC configuration, use the show vpc brief CLI command: 9K-A# show vpc brief Legend: (*) - local vPC is down, forwarding via vPC peer-link vPC domain id : 10 Peer status : peer adjacency formed ok vPC keep-alive status : peer is alive Configuration consistency status : success Per-vlan consistency status : success Type-2 inconsistency reason : Consistency Check Not Performed vPC role : primary Number of vPCs configured : 1 Peer Gateway : Enabled Dual-active excluded VLANs : - Graceful Consistency Check : Enabled Auto-recovery status : Disabled Delay-restore status : Timer is off.(timeout = 30s) Delay-restore SVI status : Timer is off.(timeout = 10s) vPC Peer-link status --------------------------------------------------------------------- id Port Status Active vlans -- ---- ------ -------------------------------------------------- 1 Po1 up 1 vPC status ---------------------------------------------------------------------- id Port Status Consistency Reason Active vlans -- ---- ------ ----------- ------ ------------ 10 Po10 up success success 1 To verify the status of the fcoe-npv feature, use the show feature-set CLI command: 9K-A# show feature-set Feature Set Name ID State -------------------- -------- -------- fex 3 uninstalled mpls 4 uninstalled fabric 7 uninstalled fcoe-npv 8 uninstalled
Indicators of Compromise
If the devices are configured as outlined in the Vulnerable Products ["#vp"] section, a possible indicator of compromise would be a relativity low Rx input rate, except for the vPC peer link, coupled with a high Tx rate for all enabled interfaces on the vPC pair of affected Nexus 9000 Series Switches. To see interface throughput statistics, use the show interface counter table CLI command: (egrep -v "0.0 0.0% 0.0 0.0%", excludes interfaces with zero statistics for Rx and Tx columns) 9K-A# sh int counter table | egrep -v "0.0 0.0% 0.0 0.0%" Collecting and processing interface statistics ... ------------------------------------------------------------------------ Port Description Intvl Rx Mbps Rx % Tx Mbps Tx % ------------------------------------------------------------------------ Ethernet1/49 vPC_Peer_Link 30/30 36078.7 90.2% 36078.7 90.2% Ethernet1/50/1 N/A 30/30 2.5 0.0% 9019.6 90.2% Ethernet1/50/2 N/A 30/30 0.0 0.0% 9019.6 90.2% port-channel36 N/A 30/30 2.5 0.0% 9019.6 90.2% port-channel100 vPC_Peer_Link 30/30 36078.7 90.2% 36078.7 90.2% 9K-B# sh int counter table | egrep -v "0.0 0.0% 0.0 0.0%" Collecting and processing interface statistics ... ------------------------------------------------------------------------- Port Description Intvl Rx Mbps Rx % Tx Mbps Tx % ------------------------------------------------------------------------- Ethernet1/49 vPC_Peer_Link 30/30 36078.3 90.2% 36078.3 90.2% Ethernet1/50/1 N/A 30/30 0.0 0.0% 9019.6 90.2% port-channel36 N/A 30/30 0.0 0.0% 9019.6 90.2% port-channel100 vPC_Peer_Link 30/30 36078.3 90.2% 36078.3 90.2% Another potential indication would be output discards. To check for output discards, use the show interface counter errors non-zero CLI command: 9K-A# sh int counter errors non-zero ------------------------------------------------------------------------- Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscards ------------------------------------------------------------------------- Eth1/49 0 0 0 0 0 426242 Eth1/50/1 0 0 0 0 0 9916163951 Eth1/50/2 0 0 0 0 0 9934560747 Po36 0 0 0 0 0 9916163951 Po100 0 0 0 0 0 426242 9K-B# sh int counter errors non-zero ------------------------------------------------------------------------- Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscards ------------------------------------------------------------------------- Eth1/50/1 0 0 0 0 0 9915689573 Po36 0 0 0 0 0 9915689573 If there are any questions regarding the output of your device or the information above, please contact Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html ["https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"]
Workarounds
There are no workarounds that address this vulnerability.
Fixed Software
Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license: https://www.cisco.com/c/en/us/products/end-user-license-agreement.html ["https://www.cisco.com/c/en/us/products/end-user-license-agreement.html"] Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades. When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page ["https://www.cisco.com/go/psirt"], to determine exposure and a complete upgrade solution. In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers. Customers Without Service Contracts Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html ["https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"] Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade. Fixed Releases Customers are advised to upgrade to an appropriate release ["https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html#fixes"] as indicated in the applicable table in this section. To help ensure a complete upgrade solution, customers should consider that this advisory is part of a bundled publication. The following page provides a complete list of bundle advisories: Cisco Event Response: March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication ["https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757"]. In the following tables, the left column lists releases of Cisco FXOS Software or Cisco NX-OS Software. The center column indicates whether a release is affected by the vulnerability described in this advisory and the first release that includes the fix for this vulnerability. The right column indicates whether a release is affected by all the vulnerabilities described in this bundle and which release includes fixes for those vulnerabilities. Although the releases listed in the right column of each table include fixes for the vulnerabilities, the fix related to the Cisco NX-OS Software Image Signature Verification Vulnerability ["https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-sig-verif"] requires a BIOS upgrade as part of the software upgrade. Customers who are upgrading the software for any of the following products are advised to refer to this advisory for further details about the BIOS upgrade and affected product IDs and BIOS versions: Nexus 3000 Series Switches Nexus 9000 Series Fabric Switches in ACI mode Nexus 9000 Series Switches in standalone NX-OS mode Nexus 9500 R-Series Line Cards and Fabric Modules Nexus 9000 Series Switches in Standalone NX-OS Mode: CSCvk44504 ["https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvk44504"] Cisco NX-OS Software Release First Fixed Release for This Vulnerability First Fixed Release for All Vulnerabilities Described in the Bundle of Advisories Prior to 7.0(3)I4 Not vulnerable 7.0(3)I7(6) 7.0(3)I4 Not vulnerable 7.0(3)I7(6) 7.0(3)I5 7.0(3)I7(5) 7.0(3)I7(6) 7.0(3)I6 7.0(3)I7(5) 7.0(3)I7(6) 7.0(3)I7 7.0(3)I7(5) 7.0(3)I7(6) 9.2 9.2(2) 9.2(2) Additional Resources For help determining the best Cisco NX-OS Software release for a Cisco Nexus Switch, administrators can refer to the following Recommended Releases documents. If a security advisory recommends a later release, Cisco recommends following the advisory guidance. Cisco MDS Series Switches ["https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/b_MDS_NX-OS_Recommended_Releases.html"] Cisco Nexus 1000V for VMware Switch ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/recommended_releases/b_Cisco_N1KV_VMware_MinRecommendedReleases.html"] Cisco Nexus 3000 Series and 3500 Series Switches ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus3000/sw/recommended_release/b_Minimum_and_Recommended_Cisco_NX-OS_Releases_for_Cisco_Nexus_3000_Series_Switches.html"] Cisco Nexus 5000 Series Switches ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/release/recommended_releases/recommended_nx-os_releases.html"] Cisco Nexus 5500 Platform Switches ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/recommended_releases/n5500_recommended_nx-os_releases.html"] Cisco Nexus 6000 Series Switches ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus6000/sw/release/recommended_releases/recommended_nx-os_releases.html"] Cisco Nexus 7000 Series Switches ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/recommended_releases/recommended_nx-os_releases.html"] Cisco Nexus 9000 Series Switches ["http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/recommended_release/b_Minimum_and_Recommended_Cisco_NX-OS_Releases_for_Cisco_Nexus_9000_Series_Switches.html"] Cisco Nexus 9000 Series ACI-Mode Switches ["https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/recommended-release/b_Recommended_Cisco_ACI_Releases.html"] For help determining the best Cisco NX-OS Software release for Cisco UCS, refer to the Recommended Releases documents in the release notes for the device.
Vulnerability Policy
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy ["https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html"]. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
Exploitation and Public Announcements
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
Source
This vulnerability was found during the resolution of a Cisco TAC support case.
Legal Disclaimer
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME. A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.



{
  "document": {
    "acknowledgments": [
      {
        "summary": "This vulnerability was found during the resolution of a Cisco TAC support case."
      }
    ],
    "category": "csaf_security_advisory",
    "csaf_version": "2.0",
    "notes": [
      {
        "category": "summary",
        "text": "A vulnerability in the Fibre Channel over Ethernet (FCoE) N-port Virtualization (NPV) protocol implementation in Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition.\r\n\r\nThe vulnerability is due to an incorrect processing of FCoE packets when the fcoe-npv feature is uninstalled.  An attacker could exploit this vulnerability by sending a stream of FCoE frames from an adjacent host to an affected device. An exploit could allow the attacker to cause packet amplification to occur, resulting in the saturation of interfaces and a DoS condition.\r\n\r\nCisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.\r\n\r\nThis advisory is available at the following link:\r\nhttps://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos [\"https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos\"]\r\n This advisory is part of the March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication, which includes 25 Cisco Security Advisories that describe 26 vulnerabilities. For a complete list of the advisories and links to them, see Cisco Event Response: March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication [\"https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757\"].",
        "title": "Summary"
      },
      {
        "category": "general",
        "text": "This vulnerability affects the following Cisco products if they are running a vulnerable release of Cisco NX-OS Software:\r\n\r\nNexus 9000 Series Switches in standalone NX-OS mode\r\n\r\nOnly the following Nexus 9000 Series PIDs are vulnerable:\r\n\r\nN9K-C92160YC-X\r\nN9K-C9272Q\r\nN9K-C9236C\r\nN9K-C93180YC-EX\r\nN9K-X9732C-EX\r\nN9K-C93180LC-EX\r\nN9K-C93180YC-FX\r\nN9K-X9736C-FX\r\n\r\nTo view the PIDs of the system, use the show inventory CLI command:\r\n\r\n\r\n\r\n\r\n9K-A# show inventory\r\nNAME: \"Chassis\",  DESCR: \"Nexus9000 C93128TX Chassis\"\r\nPID: N9K-C93128TX        ,  VID: V02 ,  SN: SAL1822TF13\r\n\r\nNAME: \"Slot 1\",  DESCR: \"1/10G-T Ethernet Module\"\r\nPID: N9K-C93128TX        ,  VID: V02 ,  SN: SAL1822TF13\r\n\r\nNAME: \"Slot 2\",  DESCR: \"40G Ethernet Expansion Module\"\r\nPID: N9K-M12PQ           ,  VID: V01 ,  SN: SAL1910AMHD\r\n\n\r\n\r\n\r\nNote: For this vulnerability to occur, all of the following conditions must be met:\r\n\r\nThe affected devices are configured as vPC peer switches.\r\nThe fcoe-npv feature must be uninstalled.\r\n\r\n See Details [\"#det\"] for more information.\r\n\r\nFor information about which Cisco NX-OS Software releases are vulnerable, see the Fixed Software [\"#fs\"] section of this advisory.\r\n Determining the Cisco NX-OS Software Release\r\nAdministrators can check the release of Cisco NX-OS Software that is running on a device by using the show version command in the device CLI. The following example shows the output of this command on a device that is running Cisco NX-OS Software Release 7.0(3)I5(1):\r\n\r\n\r\nnxos-switch# show version\r\nCisco Nexus Operating System (NX-OS) Software  TAC support: http://www.cisco.com/tac  Copyright (C) 2002-2016, Cisco and/or its affiliates.  All rights reserved.  The copyrights to certain works contained in this software are  owned by other third parties and used and distributed under their own  licenses, such as open source.  This software is provided \"as is,\" and  unless otherwise stated, there is no warranty, express or implied,   including but not limited to warranties of merchantability and fitness   for a particular purpose. Certain components of this software are   licensed under the GNU General Public License (GPL) version 2.0 or   GNU General Public License (GPL) version 3.0  or the GNU  Lesser General Public License (LGPL) Version 2.1 or   Lesser General Public License (LGPL) Version 2.0.   A copy of each such license is available at  http://www.opensource.org/licenses/gpl-2.0.php and  http://opensource.org/licenses/gpl-3.0.html and  http://www.opensource.org/licenses/lgpl-2.1.php and  http://www.gnu.org/licenses/old-licenses/library.txt.  Software    BIOS: version 07.57    NXOS: version 7.0(3)I5(1) [build 7.0(3)I5(0.9)]    BIOS compile time:  06/29/2016    NXOS image file is: bootflash:///nxos.7.0.3.I5.0.9.bin    NXOS compile time:  8/1/2016 23:00:00 [08/02/2016 00:30:32]    .    .    .",
        "title": "Vulnerable Products"
      },
      {
        "category": "general",
        "text": "Only products listed in the Vulnerable Products [\"#vp\"] section of this advisory are known to be affected by this vulnerability.\r\n Cisco has confirmed that this vulnerability does not affect the following Cisco products:\r\nFirepower 2100 Series\r\nFirepower 4100 Series Next-Generation Firewall\r\nFirepower 9300 Security Appliance\r\nMDS 9000 Series Multilayer Switches\r\nNexus 1000V Switch for Microsoft Hyper-V\r\nNexus 1000V Switch for VMware vSphere\r\nNexus 2000 Series Fabric Extenders\r\nNexus 3000 Series Switches\r\nNexus 3500 Platform Switches\r\nNexus 3600 Platform Switches\r\nNexus 5500 Platform Switches\r\nNexus 5600 Platform Switches\r\nNexus 6000 Series Switches\r\nNexus 7000 Series Switches\r\nNexus 7700 Series Switches\r\nNexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) mode\r\nNexus 9500 R-Series Line Cards and Fabric Modules\r\nUCS 6200 Series Fabric Interconnects\r\nUCS 6300 Series Fabric Interconnects\r\nUCS 6400 Series Fabric Interconnects",
        "title": "Products Confirmed Not Vulnerable"
      },
      {
        "category": "general",
        "text": "The affected devices are vulnerable when configured as outlined in the Vulnerable Products [\"#vp\"] section. The following commands will help identify these conditions:\r\nTo verify the status of a vPC configuration, use the show vpc brief CLI command:\r\n\r\n\r\n9K-A# show vpc brief\r\nLegend:\r\n(*) - local vPC is down, forwarding via vPC peer-link\r\n\r\nvPC domain id                     : 10\r\nPeer status                       : peer adjacency formed ok\r\nvPC keep-alive status             : peer is alive\r\nConfiguration consistency status  : success\r\nPer-vlan consistency status       : success\r\nType-2 inconsistency reason       : Consistency Check Not Performed\r\nvPC role                          : primary\r\nNumber of vPCs configured         : 1\r\nPeer Gateway                      : Enabled\r\nDual-active excluded VLANs        : -\r\nGraceful Consistency Check        : Enabled\r\nAuto-recovery status              : Disabled\r\nDelay-restore status              : Timer is off.(timeout = 30s)\r\nDelay-restore SVI status          : Timer is off.(timeout = 10s)\r\n\r\nvPC Peer-link status\r\n---------------------------------------------------------------------\r\nid   Port   Status Active vlans\r\n--   ----   ------ --------------------------------------------------\r\n1    Po1    up     1\r\n\r\nvPC status\r\n----------------------------------------------------------------------\r\nid   Port   Status Consistency Reason                     Active vlans\r\n--   ----   ------ ----------- ------                     ------------\r\n10   Po10   up     success     success                    1\r\n\n\r\nTo verify the status of the fcoe-npv feature, use the show feature-set CLI command:\r\n\r\n\r\n9K-A# show feature-set\r\nFeature Set Name      ID        State   --------------------  --------  -------- fex                    3          uninstalled mpls                   4          uninstalled\r\nfabric                 7          uninstalled\r\nfcoe-npv               8          uninstalled",
        "title": "Details"
      },
      {
        "category": "general",
        "text": "If the devices are configured as outlined in the Vulnerable Products [\"#vp\"] section, a possible indicator of compromise would be a relativity low Rx input rate, except for the vPC peer link, coupled with a high Tx rate for all enabled interfaces on the vPC pair of affected Nexus 9000 Series Switches.\r\n\r\nTo see interface throughput statistics, use the show interface counter table CLI command:  (egrep -v \"0.0  0.0%  0.0  0.0%\", excludes interfaces with zero statistics for Rx and Tx columns)\r\n\r\n\r\n\r\n9K-A# sh int counter table | egrep -v \"0.0      0.0%     0.0      0.0%\"\r\n\n\r\nCollecting and processing interface statistics ...\r\n\n\r\n------------------------------------------------------------------------\r\nPort            Description     Intvl    Rx Mbps  Rx %    Tx Mbps  Tx %\r\n------------------------------------------------------------------------\r\nEthernet1/49    vPC_Peer_Link   30/30    36078.7  90.2%   36078.7  90.2%\r\nEthernet1/50/1  N/A             30/30    2.5      0.0%    9019.6   90.2%\r\nEthernet1/50/2  N/A             30/30    0.0      0.0%    9019.6   90.2%\r\nport-channel36  N/A             30/30    2.5      0.0%    9019.6   90.2%\r\nport-channel100 vPC_Peer_Link   30/30    36078.7  90.2%   36078.7  90.2%\r\n9K-B# sh int counter table | egrep -v \"0.0      0.0%     0.0      0.0%\"\r\n  Collecting and processing interface statistics ...\r\n\r\n\r\n\r\n\r\n-------------------------------------------------------------------------\r\nPort            Description      Intvl    Rx Mbps  Rx %    Tx Mbps  Tx %\r\n-------------------------------------------------------------------------\r\nEthernet1/49    vPC_Peer_Link    30/30    36078.3  90.2%   36078.3  90.2%\r\nEthernet1/50/1  N/A              30/30    0.0      0.0%    9019.6   90.2%\r\nport-channel36  N/A              30/30    0.0      0.0%    9019.6   90.2%\r\nport-channel100 vPC_Peer_Link    30/30    36078.3  90.2%   36078.3  90.2%\r\n\n\r\n\r\nAnother potential indication would be output discards. To check for output discards, use the show interface counter errors non-zero CLI command:\r\n\r\n\r\n\r\n    9K-A# sh int counter errors non-zero\r\n\r\n-------------------------------------------------------------------------\r\nPort        Align-Err   FCS-Err  Xmit-Err  Rcv-Err  UnderSize OutDiscards\r\n-------------------------------------------------------------------------\r\nEth1/49             0         0         0        0          0      426242\r\nEth1/50/1           0         0         0        0          0  9916163951\r\nEth1/50/2           0         0         0        0          0  9934560747\r\nPo36                0         0         0        0          0  9916163951\r\nPo100               0         0         0        0          0      426242\r\n\r\n9K-B# sh int counter errors non-zero\r\n\r\n-------------------------------------------------------------------------\r\nPort        Align-Err   FCS-Err  Xmit-Err  Rcv-Err  UnderSize OutDiscards\r\n-------------------------------------------------------------------------\r\nEth1/50/1           0         0         0        0          0  9915689573\r\nPo36                0         0         0        0          0  9915689573\r\n\n\r\n\r\n\r\nIf there are any questions regarding the output of your device or the information above, please contact Cisco TAC:\r\nhttps://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html [\"https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html\"]",
        "title": "Indicators of Compromise"
      },
      {
        "category": "general",
        "text": "There are no workarounds that address this vulnerability.",
        "title": "Workarounds"
      },
      {
        "category": "general",
        "text": "Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:\r\nhttps://www.cisco.com/c/en/us/products/end-user-license-agreement.html [\"https://www.cisco.com/c/en/us/products/end-user-license-agreement.html\"]\r\n\r\nAdditionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.\r\n\r\nWhen considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page [\"https://www.cisco.com/go/psirt\"], to determine exposure and a complete upgrade solution.\r\n\r\nIn all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.\r\n Customers Without Service Contracts\r\nCustomers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC:\r\nhttps://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html [\"https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html\"]\r\n\r\nCustomers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.\r\n Fixed Releases\r\n\r\nCustomers are advised to upgrade to an appropriate release [\"https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html#fixes\"] as indicated in the applicable table in this section. To help ensure a complete upgrade solution, customers should consider that this advisory is part of a bundled publication. The following page provides a complete list of bundle advisories: Cisco Event Response: March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication [\"https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757\"].\r\n\r\nIn the following tables, the left column lists releases of Cisco FXOS Software or Cisco NX-OS Software. The center column indicates whether a release is affected by the vulnerability described in this advisory and the first release that includes the fix for this vulnerability. The right column indicates whether a release is affected by all the vulnerabilities described in this bundle and which release includes fixes for those vulnerabilities.\r\n\r\n\r\n\r\nAlthough the releases listed in the right column of each table include fixes for the vulnerabilities, the fix related to the Cisco NX-OS Software Image Signature Verification Vulnerability [\"https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-sig-verif\"] requires a BIOS upgrade as part of the software upgrade. Customers who are upgrading the software for any of the following products are advised to refer to this advisory for further details about the BIOS upgrade and affected product IDs and BIOS versions:\r\n\r\nNexus 3000 Series Switches\r\nNexus 9000 Series Fabric Switches in ACI mode\r\nNexus 9000 Series Switches in standalone NX-OS mode\r\nNexus 9500 R-Series Line Cards and Fabric Modules\r\n\r\n Nexus 9000 Series Switches in Standalone NX-OS Mode: CSCvk44504 [\"https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvk44504\"]\r\n\r\n                           Cisco NX-OS Software Release             First Fixed Release for This Vulnerability             First Fixed Release for All Vulnerabilities Described in the Bundle of Advisories                                         Prior to 7.0(3)I4\r\n             Not vulnerable             7.0(3)I7(6)\r\n                               7.0(3)I4             Not vulnerable             7.0(3)I7(6)\r\n                               7.0(3)I5             7.0(3)I7(5)              7.0(3)I7(6)\r\n                               7.0(3)I6             7.0(3)I7(5)             7.0(3)I7(6)                               7.0(3)I7             7.0(3)I7(5)              7.0(3)I7(6)\r\n                               9.2             9.2(2)\r\n             9.2(2)\r\nAdditional Resources\r\nFor help determining the best Cisco NX-OS Software release for a Cisco Nexus Switch, administrators can refer to the following Recommended Releases documents. If a security advisory recommends a later release, Cisco recommends following the advisory guidance.\r\n\r\n\r\nCisco MDS Series Switches [\"https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/b_MDS_NX-OS_Recommended_Releases.html\"]\r\nCisco Nexus 1000V for VMware Switch [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/recommended_releases/b_Cisco_N1KV_VMware_MinRecommendedReleases.html\"]\r\nCisco Nexus 3000 Series and 3500 Series Switches [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus3000/sw/recommended_release/b_Minimum_and_Recommended_Cisco_NX-OS_Releases_for_Cisco_Nexus_3000_Series_Switches.html\"]\r\nCisco Nexus 5000 Series Switches [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/release/recommended_releases/recommended_nx-os_releases.html\"]\r\nCisco Nexus 5500 Platform Switches [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/recommended_releases/n5500_recommended_nx-os_releases.html\"]\r\nCisco Nexus 6000 Series Switches [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus6000/sw/release/recommended_releases/recommended_nx-os_releases.html\"]\r\nCisco Nexus 7000 Series Switches [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/recommended_releases/recommended_nx-os_releases.html\"]\r\nCisco Nexus 9000 Series Switches [\"http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/recommended_release/b_Minimum_and_Recommended_Cisco_NX-OS_Releases_for_Cisco_Nexus_9000_Series_Switches.html\"]\r\nCisco Nexus 9000 Series ACI-Mode Switches [\"https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/recommended-release/b_Recommended_Cisco_ACI_Releases.html\"]\r\n  For help determining the best Cisco NX-OS Software release for Cisco UCS, refer to the Recommended Releases documents in the release notes for the device.",
        "title": "Fixed Software"
      },
      {
        "category": "general",
        "text": "To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy [\"https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html\"]. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.",
        "title": "Vulnerability Policy"
      },
      {
        "category": "general",
        "text": "The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.",
        "title": "Exploitation and Public Announcements"
      },
      {
        "category": "general",
        "text": "This vulnerability was found during the resolution of a Cisco TAC support case.",
        "title": "Source"
      },
      {
        "category": "legal_disclaimer",
        "text": "THIS DOCUMENT IS PROVIDED ON AN \"AS IS\" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.\r\n\r\nA standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.",
        "title": "Legal Disclaimer"
      }
    ],
    "publisher": {
      "category": "vendor",
      "contact_details": "Emergency Support:\r\n+1 877 228 7302 (toll-free within North America)\r\n+1 408 525 6532 (International direct-dial)\r\nNon-emergency Support:\r\nEmail: psirt@cisco.com\r\nSupport requests that are received via e-mail are typically acknowledged within 48 hours.",
      "issuing_authority": "Cisco product security incident response is the responsibility of the Cisco Product Security Incident Response Team (PSIRT). The Cisco PSIRT is a dedicated, global team that manages the receipt, investigation, and public reporting of security vulnerability information that is related to Cisco products and networks. The on-call Cisco PSIRT works 24x7 with Cisco customers, independent security researchers, consultants, industry organizations, and other vendors to identify possible security issues with Cisco products and networks.\r\nMore information can be found in Cisco Security Vulnerability Policy available at https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html",
      "name": "Cisco",
      "namespace": "https://wwww.cisco.com"
    },
    "references": [
      {
        "category": "self",
        "summary": "Cisco Nexus 9000 Series Switches Standalone NX-OS Mode Fibre Channel over Ethernet NPV Denial of Service Vulnerability",
        "url": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos"
      },
      {
        "category": "external",
        "summary": "Cisco Event Response: March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication",
        "url": "https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757"
      },
      {
        "category": "external",
        "summary": "Cisco Security Vulnerability Policy",
        "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html"
      },
      {
        "category": "external",
        "summary": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos",
        "url": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-npv-dos"
      },
      {
        "category": "external",
        "summary": "Cisco Event Response: March 2019 Cisco FXOS and NX-OS Software Security Advisory Bundled Publication",
        "url": "https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757"
      },
      {
        "category": "external",
        "summary": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html",
        "url": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"
      },
      {
        "category": "external",
        "summary": "https://www.cisco.com/c/en/us/products/end-user-license-agreement.html",
        "url": "https://www.cisco.com/c/en/us/products/end-user-license-agreement.html"
      },
      {
        "category": "external",
        "summary": "Cisco Security Advisories and Alerts page",
        "url": "https://www.cisco.com/go/psirt"
      },
      {
        "category": "external",
        "summary": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html",
        "url": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"
      },
      {
        "category": "external",
        "summary": "upgrade to an appropriate release",
        "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html#fixes"
      },
      {
        "category": "external",
        "summary": "Cisco\u0026nbsp;Event Response: March 2019 Cisco\u0026nbsp;FXOS and NX-OS Software Security Advisory Bundled Publication",
        "url": "https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-70757"
      },
      {
        "category": "external",
        "summary": "Cisco NX-OS Software Image Signature Verification Vulnerability",
        "url": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190306-nxos-sig-verif"
      },
      {
        "category": "external",
        "summary": "CSCvk44504",
        "url": "https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvk44504"
      },
      {
        "category": "external",
        "summary": "Cisco MDS Series Switches",
        "url": "https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/b_MDS_NX-OS_Recommended_Releases.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 1000V for VMware Switch",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/recommended_releases/b_Cisco_N1KV_VMware_MinRecommendedReleases.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 3000 Series and 3500 Series Switches",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus3000/sw/recommended_release/b_Minimum_and_Recommended_Cisco_NX-OS_Releases_for_Cisco_Nexus_3000_Series_Switches.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 5000 Series Switches",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/release/recommended_releases/recommended_nx-os_releases.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 5500 Platform Switches",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/recommended_releases/n5500_recommended_nx-os_releases.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 6000 Series Switches",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus6000/sw/release/recommended_releases/recommended_nx-os_releases.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 7000 Series Switches",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/recommended_releases/recommended_nx-os_releases.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 9000 Series Switches",
        "url": "http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/recommended_release/b_Minimum_and_Recommended_Cisco_NX-OS_Releases_for_Cisco_Nexus_9000_Series_Switches.html"
      },
      {
        "category": "external",
        "summary": "Cisco Nexus 9000 Series ACI-Mode Switches",
        "url": "https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/recommended-release/b_Recommended_Cisco_ACI_Releases.html"
      },
      {
        "category": "external",
        "summary": "Security Vulnerability Policy",
        "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html"
      }
    ],
    "title": "Cisco Nexus 9000 Series Switches Standalone NX-OS Mode Fibre Channel over Ethernet NPV Denial of Service Vulnerability",
    "tracking": {
      "current_release_date": "2019-03-06T16:00:00+00:00",
      "generator": {
        "date": "2022-09-03T03:39:13+00:00",
        "engine": {
          "name": "TVCE"
        }
      },
      "id": "cisco-sa-20190306-nxos-npv-dos",
      "initial_release_date": "2019-03-06T16:00:00+00:00",
      "revision_history": [
        {
          "date": "2019-03-06T15:31:41+00:00",
          "number": "1.0.0",
          "summary": "Initial public release."
        }
      ],
      "status": "final",
      "version": "1.0.0"
    }
  },
  "product_tree": {
    "branches": [
      {
        "branches": [
          {
            "branches": [
              {
                "branches": [
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I5(1)",
                    "product": {
                      "name": "7.0(3)I5(1)",
                      "product_id": "CSAFPID-230535"
                    }
                  },
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I5(2)",
                    "product": {
                      "name": "7.0(3)I5(2)",
                      "product_id": "CSAFPID-230536"
                    }
                  }
                ],
                "category": "product_version",
                "name": "7.0(3)I5"
              },
              {
                "branches": [
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I6(1)",
                    "product": {
                      "name": "7.0(3)I6(1)",
                      "product_id": "CSAFPID-230541"
                    }
                  },
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I6(2)",
                    "product": {
                      "name": "7.0(3)I6(2)",
                      "product_id": "CSAFPID-239476"
                    }
                  }
                ],
                "category": "product_version",
                "name": "7.0(3)I6"
              },
              {
                "branches": [
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I7(1)",
                    "product": {
                      "name": "7.0(3)I7(1)",
                      "product_id": "CSAFPID-230542"
                    }
                  },
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I7(2)",
                    "product": {
                      "name": "7.0(3)I7(2)",
                      "product_id": "CSAFPID-239478"
                    }
                  },
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I7(3)",
                    "product": {
                      "name": "7.0(3)I7(3)",
                      "product_id": "CSAFPID-239479"
                    }
                  },
                  {
                    "category": "service_pack",
                    "name": "7.0(3)I7(4)",
                    "product": {
                      "name": "7.0(3)I7(4)",
                      "product_id": "CSAFPID-248792"
                    }
                  }
                ],
                "category": "product_version",
                "name": "7.0(3)I7"
              },
              {
                "branches": [
                  {
                    "category": "service_pack",
                    "name": "7.0(3)IX1(2)",
                    "product": {
                      "name": "7.0(3)IX1(2)",
                      "product_id": "CSAFPID-239480"
                    }
                  },
                  {
                    "category": "service_pack",
                    "name": "7.0(3)IX1(2a)",
                    "product": {
                      "name": "7.0(3)IX1(2a)",
                      "product_id": "CSAFPID-239481"
                    }
                  }
                ],
                "category": "product_version",
                "name": "7.0(3)IX1"
              },
              {
                "branches": [
                  {
                    "category": "service_pack",
                    "name": "9.2(1)",
                    "product": {
                      "name": "9.2(1)",
                      "product_id": "CSAFPID-248793"
                    }
                  }
                ],
                "category": "product_version",
                "name": "9.2"
              }
            ],
            "category": "product_family",
            "name": "Cisco NX-OS Software"
          },
          {
            "category": "product_family",
            "name": "Cisco NX-OS Software",
            "product": {
              "name": "Cisco NX-OS Software ",
              "product_id": "CSAFPID-80720"
            }
          }
        ],
        "category": "vendor",
        "name": "Cisco"
      }
    ]
  },
  "vulnerabilities": [
    {
      "cve": "CVE-2019-1617",
      "ids": [
        {
          "system_name": "Cisco Bug ID",
          "text": "CSCvk44504"
        }
      ],
      "notes": [
        {
          "category": "other",
          "text": "Complete.",
          "title": "Affected Product Comprehensiveness"
        }
      ],
      "product_status": {
        "known_affected": [
          "CSAFPID-230535",
          "CSAFPID-230536",
          "CSAFPID-230541",
          "CSAFPID-230542",
          "CSAFPID-239476",
          "CSAFPID-239478",
          "CSAFPID-239479",
          "CSAFPID-239480",
          "CSAFPID-239481",
          "CSAFPID-248792",
          "CSAFPID-248793",
          "CSAFPID-80720"
        ]
      },
      "release_date": "2019-03-06T16:00:00+00:00",
      "remediations": [
        {
          "category": "vendor_fix",
          "details": "Cisco has released software updates that address this vulnerability.",
          "product_ids": [
            "CSAFPID-230535",
            "CSAFPID-230536",
            "CSAFPID-230541",
            "CSAFPID-230542",
            "CSAFPID-239476",
            "CSAFPID-239478",
            "CSAFPID-239479",
            "CSAFPID-239480",
            "CSAFPID-239481",
            "CSAFPID-248792",
            "CSAFPID-248793",
            "CSAFPID-80720"
          ],
          "url": "https://software.cisco.com"
        }
      ],
      "scores": [
        {
          "cvss_v3": {
            "baseScore": 7.4,
            "baseSeverity": "HIGH",
            "vectorString": "CVSS:3.0/AV:A/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:H",
            "version": "3.0"
          },
          "products": [
            "CSAFPID-230535",
            "CSAFPID-230536",
            "CSAFPID-230541",
            "CSAFPID-230542",
            "CSAFPID-239476",
            "CSAFPID-239478",
            "CSAFPID-239479",
            "CSAFPID-239480",
            "CSAFPID-239481",
            "CSAFPID-248792",
            "CSAFPID-248793",
            "CSAFPID-80720"
          ]
        }
      ],
      "title": "Nexus 9000 Series Switches Standalone Fibre Channel over Ethernet NPV Denial of Service Vulnerability"
    }
  ]
}


Log in or create an account to share your comment.




Tags
Taxonomy of the tags.


Loading...

Loading...

Loading...

Sightings

Author Source Type Date

Nomenclature

  • Seen: The vulnerability was mentioned, discussed, or seen somewhere by the user.
  • Confirmed: The vulnerability is confirmed from an analyst perspective.
  • Exploited: This vulnerability was exploited and seen by the user reporting the sighting.
  • Patched: This vulnerability was successfully patched by the user reporting the sighting.
  • Not exploited: This vulnerability was not exploited or seen by the user reporting the sighting.
  • Not confirmed: The user expresses doubt about the veracity of the vulnerability.
  • Not patched: This vulnerability was not successfully patched by the user reporting the sighting.