CVE-2026-79982 (GCVE-0-2026-79982)

Vulnerability from cvelistv5 – Published: 2026-10-23 19:56 – Updated: 2026-10-23 19:56
VLAI
Title
Out-of-bounds write in the USB Bluetooth HCI transport class when a controller-to-host HCI packet exceeds the bulk endpoint maximum packet size
Summary
The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.
Severity
8.8 (High)
CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H
CWE
Assigner
zephyr CNA under the mitre root
CNA scorecard B 77/100 over 202 records in the last 180 days details
References
Impacted products
Vendor Product Version CPE status
zephyrproject zephyr Affected: 3.3.0 , ≤ 4.4.2 (semver)
guessed Create a notification for this product.
Show details on NVD website
To clipboard 

{
  "containers": {
    "cna": {
      "affected": [
        {
          "collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
          "defaultStatus": "unaffected",
          "packageName": "zephyr",
          "product": "zephyr",
          "programFiles": [
            "subsys/usb/device_next/class/bt_hci.c"
          ],
          "programRoutines": [
            {
              "name": "bt_hci_tx_sync_in"
            }
          ],
          "vendor": "zephyrproject",
          "versions": [
            {
              "lessThanOrEqual": "4.4.2",
              "status": "affected",
              "version": "3.3.0",
              "versionType": "semver"
            }
          ]
        }
      ],
      "descriptions": [
        {
          "lang": "en",
          "value": "The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf-\u003edata, bt_buf-\u003elen) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool.\n\nThe device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization.\n\nBecause net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n \u2014 the usual production setting \u2014 silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly."
        }
      ],
      "metrics": [
        {
          "cvssV3_1": {
            "baseScore": 8.8,
            "baseSeverity": "HIGH",
            "vectorString": "CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H",
            "version": "3.1"
          },
          "format": "CVSS"
        }
      ],
      "problemTypes": [
        {
          "descriptions": [
            {
              "cweId": "CWE-787",
              "description": "bounds",
              "lang": "en",
              "type": "CWE"
            }
          ]
        }
      ],
      "providerMetadata": {
        "dateUpdated": "2026-10-23T19:56:19.432Z",
        "orgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
        "shortName": "zephyr"
      },
      "references": [
        {
          "name": "Fix commit",
          "tags": [
            "patch"
          ],
          "url": "https://github.com/zephyrproject-rtos/zephyr/commit/0419defd2391652edc27689d206fcd9c48439d4a"
        },
        {
          "name": "GHSA-w5px-w97v-c3hj",
          "url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-w5px-w97v-c3hj"
        }
      ],
      "title": "Out-of-bounds write in the USB Bluetooth HCI transport class when a controller-to-host HCI packet exceeds the bulk endpoint maximum packet size",
      "x_generator": {
        "engine": "cvelib 1.8.0"
      }
    }
  },
  "cveMetadata": {
    "assignerOrgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
    "assignerShortName": "zephyr",
    "cveId": "CVE-2026-79982",
    "datePublished": "2026-10-23T19:56:19.432Z",
    "dateReserved": "2026-08-25T16:06:38.229Z",
    "dateUpdated": "2026-10-23T19:56:19.432Z",
    "state": "PUBLISHED"
  },
  "dataType": "CVE_RECORD",
  "dataVersion": "5.2",
  "vulnerability-lookup:meta": {
    "epss": {
      "cve": "CVE-2026-79982",
      "date": "2026-10-29",
      "epss": "0.00229",
      "percentile": "0.13767"
    },
    "nvd": {
      "cve": {
        "affected": [
          {
            "affectedData": [
              {
                "collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
                "defaultStatus": "unaffected",
                "packageName": "zephyr",
                "product": "zephyr",
                "programFiles": [
                  "subsys/usb/device_next/class/bt_hci.c"
                ],
                "programRoutines": [
                  {
                    "name": "bt_hci_tx_sync_in"
                  }
                ],
                "vendor": "zephyrproject",
                "versions": [
                  {
                    "lessThanOrEqual": "4.4.2",
                    "status": "affected",
                    "version": "3.3.0",
                    "versionType": "semver"
                  }
                ]
              }
            ],
            "source": "vulnerabilities@zephyrproject.org"
          }
        ],
        "cveTags": [],
        "descriptions": [
          {
            "lang": "en",
            "value": "The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf-\u003edata, bt_buf-\u003elen) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool.\n\nThe device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization.\n\nBecause net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n \u2014 the usual production setting \u2014 silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly."
          }
        ],
        "id": "CVE-2026-79982",
        "lastModified": "2026-10-26T13:52:21.763",
        "metrics": {
          "cvssMetricV31": [
            {
              "cvssData": {
                "attackComplexity": "LOW",
                "attackVector": "ADJACENT_NETWORK",
                "availabilityImpact": "HIGH",
                "baseScore": 8.8,
                "baseSeverity": "HIGH",
                "confidentialityImpact": "HIGH",
                "integrityImpact": "HIGH",
                "privilegesRequired": "NONE",
                "scope": "UNCHANGED",
                "userInteraction": "NONE",
                "vectorString": "CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H",
                "version": "3.1"
              },
              "exploitabilityScore": 2.8,
              "impactScore": 5.9,
              "source": "vulnerabilities@zephyrproject.org",
              "type": "Secondary"
            }
          ]
        },
        "published": "2026-10-23T20:17:28.167",
        "references": [
          {
            "source": "vulnerabilities@zephyrproject.org",
            "url": "https://github.com/zephyrproject-rtos/zephyr/commit/0419defd2391652edc27689d206fcd9c48439d4a"
          },
          {
            "source": "vulnerabilities@zephyrproject.org",
            "url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-w5px-w97v-c3hj"
          }
        ],
        "sourceIdentifier": "vulnerabilities@zephyrproject.org",
        "vulnStatus": "Awaiting Analysis",
        "weaknesses": [
          {
            "description": [
              {
                "lang": "en",
                "value": "CWE-787"
              }
            ],
            "source": "vulnerabilities@zephyrproject.org",
            "type": "Secondary"
          }
        ]
      }
    }
  }
}



Log in or create an account to share your comment.




Tags
Taxonomy of the tags.




Drag nodes to arrange them. Double-click a related vulnerability to open it, or a source to visit its link. The Physics button on the left tunes the layout and the simulation; the legend at the bottom left hides or shows nodes by kind and by sighting type.

Forecast uses a logistic model when the trend is rising, or an exponential decay model when the trend is falling. Fitted via linearized least squares.

Sightings

Author Source Type Date Other

Nomenclature

  • Seen: The vulnerability was mentioned, discussed, or observed by the user.
  • Confirmed: The vulnerability has been validated from an analyst's perspective.
  • Published Proof of Concept: A public proof of concept is available for this vulnerability.
  • Exploited: The vulnerability was observed as exploited by the user who reported the sighting.
  • Patched: The vulnerability was observed as successfully patched by the user who reported the sighting.
  • Not exploited: The vulnerability was not observed as exploited by the user who reported the sighting.
  • Not confirmed: The user expressed doubt about the validity of the vulnerability.
  • Not patched: The vulnerability was not observed as successfully patched by the user who reported the sighting.
Vulnerability timeline

Sightings and recorded dates, grouped by day · UTC

JSON
How durations are calculated

Following the VTEM framework (Black Hat USA 2015), time to patch starts when the vendor or a coordinator was informed, total time to patch at discovery, and disclosure to patch at public disclosure; vendor response time runs from the report to its acknowledgement. Time to exploit and time unpatched start at the earliest discovery or report, falling back to public disclosure. Unpatched time ends at the first recorded patch, or the calculation time when no patch is recorded. Exploitation to patch shows the interval between those two events; a published proof of concept is a public exploit, not exploitation.

Each result shows its source dates. A negative interval means the end event came first; when date-only inputs leave the order open, the result says so. Date-only inputs are approximate. The earliest evidence wins: KEV report dates and sightings are labelled as such. Records describing another vulnerability are listed but never calculated from, and a PoC alone does not establish exploitation. Missing patch evidence does not prove that no patch exists. Filters below change the event list only.

Loading timeline…




    Related by attack behaviour

    Vulnerabilities whose description is nearest to this one in the vector space of the CIRCL/vulnerability-attack-technique-biencoder model. This is a similarity search over the bi-encoder space (plain cosine), not a classification, and it has no measured accuracy.