cisco-sa-20190123-firepowertds-bypass
Vulnerability from csaf_cisco
Published
2019-01-23 14:00
Modified
2019-01-23 14:00
Summary
Cisco Firepower Threat Defense Software Packet Inspection and Enforcement Bypass Vulnerability
Notes
Summary
A vulnerability in the data acquisition (DAQ) component of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to bypass configured access control policies or cause a denial of service (DoS) condition.
The vulnerability exists because the affected software improperly manages system memory resources when inspecting traffic. An attacker could exploit this vulnerability by generating specific traffic patterns for the software to inspect. A successful exploit could allow the attacker to exhaust system memory resources used for traffic inspection. Depending on the configuration, the FTD Software could fail open and cease to inspect traffic or fail closed and result in a DoS condition. This vulnerability may require manual intervention to restore the software.
Cisco has released software updates that address this vulnerability. There are workarounds that address this vulnerability.
This advisory is available at the following link:
https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass ["https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass"]
Vulnerable Products
This vulnerability affects Cisco Firepower Threat Defense Software Release 6.3.0 only when running on Firepower 4100 or Firepower 9300 Series Platforms.
Determine a Vulnerable FTD Software Configuration
To verify whether the FTD Software has a vulnerable configuration, administrators can check access control policies and general configurations. To be considered vulnerable, the configuration must have all of the following:
Access control rules that perform URL filtering or invoke file/malware inspection
SSL hardware acceleration enabled (default setting)
Access control policy advanced settings that do not specify an associated SSL policy to handle encrypted traffic (default setting)
Note: If the Snort Fail Open: Busy option under Inline Sets > Advanced is enabled, exploit attempts can cause traffic to pass through without inspection when the Snort process is busy. If the Busy option is not enabled, exploit attempts can cause a DoS condition.
Determine the Cisco Firepower System Software Release
To determine which Cisco Firepower System Software release is running on a device, administrators can log in to the device, use the show version command in the CLI, and refer to the output of the command. The following example shows the output of the command for a device that is running Cisco Firepower System Software Release 6.3.0:
> show version
-------[ ftd.domain.com ]-------- Model : Cisco Firepower 4140 Threat Defense (76) Version 6.3.0 (Build 83) UUID : 06870e8a-15a7-11e9-b733-a3ffca9e3696 Rules update version : 2019-01-14-001-vrt VDB version : 299 ----------------------------------------------------
Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products ["#vp"] section of this advisory are known to be affected by this vulnerability.
Indicators of Compromise
Exploitation of this vulnerability can lead to a decrease in available system memory. Administrators can issue the show blocks command; an available block count in the CNT column that shows a continued decrease in the memory blocks of size 9344 could indicate active exploitation.
# show blocks
SIZE MAX LOW CNT 0 2700 2693 2700 4 100 99 99 80 1196 1135 1196 256 4148 3953 4124 1550 6494 6405 6489 2048 100 100 100 2560 164 164 164 4096 100 100 100 8192 100 100 100 9344 48552 516 535 16384 100 100 100 65536 16 16 16
A depletion of the memory blocks of size 9344 could cause traffic inspection to cease and may prevent network policies from being applied. If these conditions are observed, customers are advised to contact the Cisco Technical Assistance Center (TAC) to determine whether the device has been compromised by exploitation of this vulnerability.
Workarounds
Disabling SSL hardware acceleration, which is enabled by default in FTD Software Release 6.3.0, mitigates this vulnerability when no SSL policy is applied. Configurations with SSL policies enabled are not vulnerable.
Administrators can issue the system support ssl-hw-offload disable command in the CLI to disable SSL hardware acceleration. This command will reboot the device.
ftd# system support ssl-hw-offload disable
Fixed Software
Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license: https://www.cisco.com/c/en/us/products/end-user-license-agreement.html ["https://www.cisco.com/c/en/us/products/end-user-license-agreement.html"]
Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.
When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page ["https://www.cisco.com/go/psirt"], to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
Customers Without Service Contracts
Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html ["https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"]
Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.
Fixed Releases
In the following table, the left column lists releases of Cisco Firepower System Software. The right column indicates whether a release is affected by the vulnerability described in this advisory and the first release that includes the fix for this vulnerability.
Cisco Firepower System Software Release First Fixed Release 6.1.0 Not vulnerable
6.2.0 Not vulnerable 6.2.1 Not vulnerable 6.2.2 Not vulnerable 6.2.3 Not vulnerable 6.3.01 Affected; apply 6.3.0 Hotfix B 16.3.0 Build 85 or later is not vulnerable.
Vulnerability Policy
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy ["https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html"]. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
Exploitation and Public Announcements
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
Source
This vulnerability was found during the resolution of a Cisco TAC support case.
Legal Disclaimer
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.
{ "document": { "acknowledgments": [ { "summary": "This vulnerability was found during the resolution of a Cisco TAC support case." } ], "category": "csaf_security_advisory", "csaf_version": "2.0", "notes": [ { "category": "summary", "text": "A vulnerability in the data acquisition (DAQ) component of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to bypass configured access control policies or cause a denial of service (DoS) condition.\r\n\r\nThe vulnerability exists because the affected software improperly manages system memory resources when inspecting traffic. An attacker could exploit this vulnerability by generating specific traffic patterns for the software to inspect. A successful exploit could allow the attacker to exhaust system memory resources used for traffic inspection. Depending on the configuration, the FTD Software could fail open and cease to inspect traffic or fail closed and result in a DoS condition. This vulnerability may require manual intervention to restore the software.\r\n\r\nCisco has released software updates that address this vulnerability. There are workarounds that address this vulnerability.\r\n\r\nThis advisory is available at the following link:\r\nhttps://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass [\"https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass\"]", "title": "Summary" }, { "category": "general", "text": "This vulnerability affects Cisco Firepower Threat Defense Software Release 6.3.0 only when running on Firepower 4100 or Firepower 9300 Series Platforms.\r\n\r\nDetermine a Vulnerable FTD Software Configuration\r\n\r\nTo verify whether the FTD Software has a vulnerable configuration, administrators can check access control policies and general configurations. To be considered vulnerable, the configuration must have all of the following:\r\n\r\nAccess control rules that perform URL filtering or invoke file/malware inspection\r\nSSL hardware acceleration enabled (default setting)\r\nAccess control policy advanced settings that do not specify an associated SSL policy to handle encrypted traffic (default setting)\r\n Note: If the Snort Fail Open: Busy option under Inline Sets \u003e Advanced is enabled, exploit attempts can cause traffic to pass through without inspection when the Snort process is busy. If the Busy option is not enabled, exploit attempts can cause a DoS condition.\r\n\r\n\r\nDetermine the Cisco Firepower System Software Release\r\n\r\nTo determine which Cisco Firepower System Software release is running on a device, administrators can log in to the device, use the show version command in the CLI, and refer to the output of the command. The following example shows the output of the command for a device that is running Cisco Firepower System Software Release 6.3.0:\r\n\r\n\r\n\u003e show version\r\n-------[ ftd.domain.com ]-------- Model : Cisco Firepower 4140 Threat Defense (76) Version 6.3.0 (Build 83) UUID : 06870e8a-15a7-11e9-b733-a3ffca9e3696 Rules update version : 2019-01-14-001-vrt VDB version : 299 ----------------------------------------------------", "title": "Vulnerable Products" }, { "category": "general", "text": "Only products listed in the Vulnerable Products [\"#vp\"] section of this advisory are known to be affected by this vulnerability.", "title": "Products Confirmed Not Vulnerable" }, { "category": "general", "text": "Exploitation of this vulnerability can lead to a decrease in available system memory. Administrators can issue the show blocks command; an available block count in the CNT column that shows a continued decrease in the memory blocks of size 9344 could indicate active exploitation.\r\n\r\n\r\n# show blocks\r\n SIZE MAX LOW CNT 0 2700 2693 2700 4 100 99 99 80 1196 1135 1196 256 4148 3953 4124 1550 6494 6405 6489 2048 100 100 100 2560 164 164 164 4096 100 100 100 8192 100 100 100 9344 48552 516 535 16384 100 100 100 65536 16 16 16\r\n\r\nA depletion of the memory blocks of size 9344 could cause traffic inspection to cease and may prevent network policies from being applied. If these conditions are observed, customers are advised to contact the Cisco Technical Assistance Center (TAC) to determine whether the device has been compromised by exploitation of this vulnerability.", "title": "Indicators of Compromise" }, { "category": "general", "text": "Disabling SSL hardware acceleration, which is enabled by default in FTD Software Release 6.3.0, mitigates this vulnerability when no SSL policy is applied. Configurations with SSL policies enabled are not vulnerable.\r\n\r\nAdministrators can issue the system support ssl-hw-offload disable command in the CLI to disable SSL hardware acceleration. This command will reboot the device.\r\n\r\n\r\nftd# system support ssl-hw-offload disable", "title": "Workarounds" }, { "category": "general", "text": "Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license: https://www.cisco.com/c/en/us/products/end-user-license-agreement.html [\"https://www.cisco.com/c/en/us/products/end-user-license-agreement.html\"]\r\n\r\nAdditionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.\r\n\r\nWhen considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page [\"https://www.cisco.com/go/psirt\"], to determine exposure and a complete upgrade solution.\r\n\r\nIn all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.\r\n\r\nCustomers Without Service Contracts\r\n\r\nCustomers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html [\"https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html\"]\r\n\r\nCustomers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.\r\n\r\nFixed Releases\r\n\r\nIn the following table, the left column lists releases of Cisco Firepower System Software. The right column indicates whether a release is affected by the vulnerability described in this advisory and the first release that includes the fix for this vulnerability.\r\n Cisco Firepower System Software Release First Fixed Release 6.1.0 Not vulnerable\r\n 6.2.0 Not vulnerable 6.2.1 Not vulnerable 6.2.2 Not vulnerable 6.2.3 Not vulnerable 6.3.01 Affected; apply 6.3.0 Hotfix B 16.3.0 Build 85 or later is not vulnerable.", "title": "Fixed Software" }, { "category": "general", "text": "To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy [\"https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html\"]. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.", "title": "Vulnerability Policy" }, { "category": "general", "text": "The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.", "title": "Exploitation and Public Announcements" }, { "category": "general", "text": "This vulnerability was found during the resolution of a Cisco TAC support case.", "title": "Source" }, { "category": "legal_disclaimer", "text": "THIS DOCUMENT IS PROVIDED ON AN \"AS IS\" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.\r\n\r\nA standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.", "title": "Legal Disclaimer" } ], "publisher": { "category": "vendor", "contact_details": "Emergency Support:\r\n+1 877 228 7302 (toll-free within North America)\r\n+1 408 525 6532 (International direct-dial)\r\nNon-emergency Support:\r\nEmail: psirt@cisco.com\r\nSupport requests that are received via e-mail are typically acknowledged within 48 hours.", "issuing_authority": "Cisco product security incident response is the responsibility of the Cisco Product Security Incident Response Team (PSIRT). The Cisco PSIRT is a dedicated, global team that manages the receipt, investigation, and public reporting of security vulnerability information that is related to Cisco products and networks. The on-call Cisco PSIRT works 24x7 with Cisco customers, independent security researchers, consultants, industry organizations, and other vendors to identify possible security issues with Cisco products and networks.\r\nMore information can be found in Cisco Security Vulnerability Policy available at https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html", "name": "Cisco", "namespace": "https://wwww.cisco.com" }, "references": [ { "category": "self", "summary": "Cisco Firepower Threat Defense Software Packet Inspection and Enforcement Bypass Vulnerability", "url": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass" }, { "category": "external", "summary": "Cisco Security Vulnerability Policy", "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html" }, { "category": "external", "summary": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass", "url": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190123-firepowertds-bypass" }, { "category": "external", "summary": "https://www.cisco.com/c/en/us/products/end-user-license-agreement.html", "url": "https://www.cisco.com/c/en/us/products/end-user-license-agreement.html" }, { "category": "external", "summary": "Cisco Security Advisories and Alerts page", "url": "https://www.cisco.com/go/psirt" }, { "category": "external", "summary": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html", "url": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html" }, { "category": "external", "summary": "Security Vulnerability Policy", "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html" } ], "title": "Cisco Firepower Threat Defense Software Packet Inspection and Enforcement Bypass Vulnerability", "tracking": { "current_release_date": "2019-01-23T14:00:00+00:00", "generator": { "date": "2022-09-03T03:39:04+00:00", "engine": { "name": "TVCE" } }, "id": "cisco-sa-20190123-firepowertds-bypass", "initial_release_date": "2019-01-23T14:00:00+00:00", "revision_history": [ { "date": "2019-01-23T13:36:28+00:00", "number": "1.0.0", "summary": "Initial public release." } ], "status": "final", "version": "1.0.0" } }, "product_tree": { "branches": [ { "branches": [ { "branches": [ { "branches": [ { "category": "service_pack", "name": "6.3.0", "product": { "name": "6.3.0", "product_id": "CSAFPID-251759" } } ], "category": "product_version", "name": "6.3" } ], "category": "product_family", "name": "Cisco Firepower Threat Defense Software" } ], "category": "vendor", "name": "Cisco" } ] }, "vulnerabilities": [ { "cve": "CVE-2019-1669", "ids": [ { "system_name": "Cisco Bug ID", "text": "CSCvo02577" } ], "notes": [ { "category": "other", "text": "Complete.", "title": "Affected Product Comprehensiveness" } ], "product_status": { "known_affected": [ "CSAFPID-251759" ] }, "release_date": "2019-01-23T14:00:00+00:00", "remediations": [ { "category": "vendor_fix", "details": "Cisco has released software updates that address this vulnerability.", "product_ids": [ "CSAFPID-251759" ], "url": "https://software.cisco.com" }, { "category": "workaround", "details": "Disabling SSL hardware acceleration, which is enabled by default in FTD Software Release 6.3.0, mitigates this vulnerability when no SSL policy is applied. Configurations with SSL policies enabled are not vulnerable.\r\n\r\nAdministrators can issue the system support ssl-hw-offload disable command in the CLI to disable SSL hardware acceleration. This command will reboot the device.\r\n\r\n\r\nftd# system support ssl-hw-offload disable", "product_ids": [ "CSAFPID-251759" ] } ], "scores": [ { "cvss_v3": { "baseScore": 8.6, "baseSeverity": "HIGH", "vectorString": "CVSS:3.0/AV:N/AC:L/PR:N/UI:N/S:C/C:N/I:H/A:N", "version": "3.0" }, "products": [ "CSAFPID-251759" ] } ], "title": "Cisco Firepower Threat Defense Software Packet Inspection and Enforcement Bypass Vulnerability" } ] }
Loading...
Loading...
Sightings
Author | Source | Type | Date |
---|
Nomenclature
- Seen: The vulnerability was mentioned, discussed, or seen somewhere by the user.
- Confirmed: The vulnerability is confirmed from an analyst perspective.
- Exploited: This vulnerability was exploited and seen by the user reporting the sighting.
- Patched: This vulnerability was successfully patched by the user reporting the sighting.
- Not exploited: This vulnerability was not exploited or seen by the user reporting the sighting.
- Not confirmed: The user expresses doubt about the veracity of the vulnerability.
- Not patched: This vulnerability was not successfully patched by the user reporting the sighting.