cisco-sa-ipsla-za3srrpp
Vulnerability from csaf_cisco
Published
2021-09-08 16:00
Modified
2021-10-08 12:49
Summary
Cisco IOS XR Software IP Service Level Agreements and Two-Way Active Measurement Protocol Denial of Service Vulnerability

Notes

Summary
A vulnerability in the IP Service Level Agreements (IP SLA) responder and Two-Way Active Measurement Protocol (TWAMP) features of Cisco IOS XR Software could allow an unauthenticated, remote attacker to cause device packet memory to become exhausted or cause the IP SLA process to crash, resulting in a denial of service (DoS) condition. This vulnerability exists because socket creation failures are mishandled during the IP SLA and TWAMP processes. An attacker could exploit this vulnerability by sending specific IP SLA or TWAMP packets to an affected device. A successful exploit could allow the attacker to exhaust the packet memory, which will impact other processes, such as routing protocols, or crash the IP SLA process. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is part of the September 2021 release of the Cisco IOS XR Software Security Advisory Bundled Publication. For a complete list of the advisories and links to them, see Cisco Event Response: September 2021 Cisco IOS XR Software Security Advisory Bundled Publication ["https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-74637"].
Vulnerable Products
This vulnerability affects Cisco devices if they are running a vulnerable release of Cisco IOS XR Software and have the IP SLA responder feature enabled. For information about which Cisco software releases are vulnerable, see the Fixed Software ["#fs"] section of this advisory. Determine the IP SLA Responder Configuration To determine whether the IP SLA responder is enabled on a device, use the show running-config ipsla CLI command. If the IP SLA feature is configured with the keywords responder or responder twamp, the device is affected by this vulnerability. The following example shows the output for a device that has the IP SLA responder enabled: RP/0/RP0/CPU0:IOSXR# show running-config ipsla ipsla responder ! RP/0/RP0/CPU0:IOSXR# The following example shows the output for a device that has the IP SLA responder enabled with TWAMP: RP/0/RP0/CPU0:IOSXR# show running-config ipsla ipsla responder twamp ! RP/0/RP0/CPU0:IOSXR# Note: Devices that are configured purely as initiators in the IP SLA process with the ipsla operation are not affected unless they also have the responder or responder twamp configured.
Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products ["#vp"] section of this advisory are known to be affected by this vulnerability. Cisco has confirmed that this vulnerability does not affect the following Cisco products: IOS Software IOS XE Software NX-OS Software
Workarounds
There are no workarounds that address this vulnerability. However, administrators may choose to do the following as a mitigation: If IP SLA responder is configured with a key chain and a key-string password, then only authenticated attackers can exploit this vulnerability. To enable authentication on the IP SLA responder, use the show running-config ipsla and the show run key chain commands, as shown in the following example: RP/0/RP0/CPU0:IOSXR# show running-config ipsla ipsla key-chain 1 responder ! ! RP/0/RP0/CPU0:IOSXR# RP/0/RP0/CPU0:IOSXR#show run key chain key chain 1 key 1 key-string password 060506324F41584B56 ! ! While this mitigation has been deployed and was proven successful in a test environment, customers should determine the applicability and effectiveness in their own environment and under their own use conditions. Customers should be aware that any workaround or mitigation that is implemented may negatively impact the functionality or performance of their network based on intrinsic customer deployment scenarios and limitations. Customers should not deploy any workarounds or mitigations before first evaluating the applicability to their own environment and any impact to such environment.
Fixed Software
Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license: https://www.cisco.com/c/en/us/products/end-user-license-agreement.html ["https://www.cisco.com/c/en/us/products/end-user-license-agreement.html"] Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades. When considering software upgrades ["https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html#fixes"], customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page ["https://www.cisco.com/go/psirt"], to determine exposure and a complete upgrade solution. In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers. Customers Without Service Contracts Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html ["https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"] Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade. Fixed Releases In the following table, the left column lists Cisco software release trains. The center column indicates which specific releases are affected by this vulnerability. The right column indicates the first fixed release. Cisco IOS XR Software Release Affected Releases First Fixed Release for This Vulnerability 5.3 and earlier All Migrate to a fixed release. 6.0 All Migrate to a fixed release. 6.1 All Migrate to a fixed release. 6.2 6.2.1, 6.2.2 6.2.3 6.3 6.3.1 6.3.2, 6.3.3 6.4 Not vulnerable. Not vulnerable. 6.5 6.5.2, 6.5.3 Migrate to a fixed release. 6.6 All Migrate to a fixed release. 6.7 All Fixed in 6.7.4 for ip sla responder configurations. ip sla responder twamp configurations are vulnerable; migrate to a fixed release. 7.0 All Migrate to a fixed release. 7.1 All Migrate to a fixed release. 7.2 All 7.2.2 7.3 and later Not affected. Not affected. Cisco has released the following SMUs to address this vulnerability. Customers who require SMUs for platforms or releases that are not listed are advised to contact their support organization. The SMUs in the following table address Cisco Bug ID CSCvw32825 ["https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw32825"] (for ip sla responder configurations). Cisco IOS XR Software Release Platform SMU Name 6.3.3 ASR9K-PX asr9k-px-6.3.3.CSCvw32825 6.4.2 ASR9K-X64 asr9k-x64-6.4.2.CSCvw32825 6.5.3 ASR9K-PX asr9k-px-6.5.3.CSCvw32825 6.6.3 ASR9K-PX asr9k-px-6.6.3.CSCvw32825 ASR9K-X64 asr9k-x64-6.6.3.CSCvw32825 NCS5500 ncs5500-6.6.3.CSCvw32825 6.7.3 ASR9K-PX asr9k-px-6.7.3.CSCvw32825 7.1.2 NCS540 ncs540-7.1.2.CSCvw32825 NCS560 ncs560-7.1.2.CSCvw32825 NCS5500 ncs5500-7.1.2.CSCvw32825 7.1.3 ASR9K-X64 asr9k-x64-7.1.3.CSCvw32825 The SMUs in the following table address Cisco Bug ID CSCvw61840 ["https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw61840"] (for ip sla responder twamp configurations). Cisco IOS XR Software Release Platform SMU Name 6.3.3 ASR9K-PX asr9k-px-6.3.3.CSCvw61840 6.5.3 NCS5500 ncs5500-6.5.3.CSCvw61840 6.6.3 ASR9K-PX asr9k-px-6.6.3.CSCvw61840 ASR9K-X64 asr9k-x64-6.6.3.CSCvw61840 7.1.3 ASR9K-X64 asr9k-x64-7.1.3.CSCvw61840 The Cisco Product Security Incident Response Team (PSIRT) validates only the affected and fixed release information that is documented in this advisory.
Vulnerability Policy
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy ["https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html"]. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
Exploitation and Public Announcements
The Cisco PSIRT is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
Source
This vulnerability was found during the resolution of a Cisco TAC support case.
Legal Disclaimer
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME. A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.



{
  "document": {
    "acknowledgments": [
      {
        "summary": "This vulnerability was found during the resolution of a Cisco TAC support case."
      }
    ],
    "category": "csaf_security_advisory",
    "csaf_version": "2.0",
    "notes": [
      {
        "category": "summary",
        "text": "A vulnerability in the IP Service Level Agreements (IP SLA) responder and Two-Way Active Measurement Protocol (TWAMP) features of Cisco IOS XR Software could allow an unauthenticated, remote attacker to cause device packet memory to become exhausted or cause the IP SLA process to crash, resulting in a denial of service (DoS) condition.\r\n\r\nThis vulnerability exists because socket creation failures are mishandled during the IP SLA and TWAMP processes. An attacker could exploit this vulnerability by sending specific IP SLA or TWAMP packets to an affected device. A successful exploit could allow the attacker to exhaust the packet memory, which will impact other processes, such as routing protocols, or crash the IP SLA process.\r\n\r\nCisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.\r\n\r\n\r\n\r\nThis advisory is part of the September 2021 release of the Cisco IOS XR Software Security Advisory Bundled Publication. For a complete list of the advisories and links to them, see Cisco Event Response: September 2021 Cisco IOS XR Software Security Advisory Bundled Publication [\"https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-74637\"].",
        "title": "Summary"
      },
      {
        "category": "general",
        "text": "This vulnerability affects Cisco devices if they are running a vulnerable release of Cisco IOS XR Software and have the IP SLA responder feature enabled.\r\n\r\nFor information about which Cisco software releases are vulnerable, see the Fixed Software [\"#fs\"] section of this advisory.\r\n  Determine the IP SLA Responder Configuration\r\nTo determine whether the IP SLA responder is enabled on a device, use the show running-config ipsla CLI command. If the IP SLA feature is configured with the keywords responder or responder twamp, the device is affected by this vulnerability.\r\n\r\nThe following example shows the output for a device that has the IP SLA responder enabled:\r\n\r\n\r\nRP/0/RP0/CPU0:IOSXR# show running-config ipsla\r\nipsla\r\n responder\r\n !\r\nRP/0/RP0/CPU0:IOSXR#\r\n\r\nThe following example shows the output for a device that has the IP SLA responder enabled with TWAMP:\r\n\r\n\r\nRP/0/RP0/CPU0:IOSXR# show running-config ipsla\r\nipsla\r\n responder\r\n  twamp\r\n !\r\nRP/0/RP0/CPU0:IOSXR#\r\n\r\nNote: Devices that are configured purely as initiators in the IP SLA process with the ipsla operation are not affected unless they also have the responder or responder twamp configured.",
        "title": "Vulnerable Products"
      },
      {
        "category": "general",
        "text": "Only products listed in the Vulnerable Products [\"#vp\"] section of this advisory are known to be affected by this vulnerability.\r\n\r\nCisco has confirmed that this vulnerability does not affect the following Cisco products:\r\n\r\nIOS Software\r\nIOS XE Software\r\nNX-OS Software",
        "title": "Products Confirmed Not Vulnerable"
      },
      {
        "category": "general",
        "text": "There are no workarounds that address this vulnerability. However, administrators may choose to do the following as a mitigation:\r\n\r\nIf IP SLA responder is configured with a key chain and a key-string password, then only authenticated attackers can exploit this vulnerability. To enable authentication on the IP SLA responder, use the show running-config ipsla and the show run key chain commands, as shown in the following example:\r\n\r\n\r\nRP/0/RP0/CPU0:IOSXR# show running-config ipsla\r\nipsla\r\n key-chain 1\r\n responder\r\n !\r\n!\r\nRP/0/RP0/CPU0:IOSXR#\r\nRP/0/RP0/CPU0:IOSXR#show run key chain\r\nkey chain 1\r\n key 1\r\n  key-string password 060506324F41584B56\r\n !\r\n!\r\n\r\nWhile this mitigation has been deployed and was proven successful in a test environment, customers should determine the applicability and effectiveness in their own environment and under their own use conditions. Customers should be aware that any workaround or mitigation that is implemented may negatively impact the functionality or performance of their network based on intrinsic customer deployment scenarios and limitations. Customers should not deploy any workarounds or mitigations before first evaluating the applicability to their own environment and any impact to such environment.",
        "title": "Workarounds"
      },
      {
        "category": "general",
        "text": "Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:\r\nhttps://www.cisco.com/c/en/us/products/end-user-license-agreement.html [\"https://www.cisco.com/c/en/us/products/end-user-license-agreement.html\"]\r\n\r\nAdditionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.\r\n\r\nWhen considering software upgrades [\"https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html#fixes\"], customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page [\"https://www.cisco.com/go/psirt\"], to determine exposure and a complete upgrade solution.\r\n\r\nIn all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.\r\n  Customers Without Service Contracts\r\nCustomers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html [\"https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html\"]\r\n\r\nCustomers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.\r\n      Fixed Releases\r\nIn the following table, the left column lists Cisco software release trains. The center column indicates which specific releases are affected by this vulnerability. The right column indicates the first fixed release.\r\n        Cisco IOS XR Software Release  Affected Releases  First Fixed Release for This Vulnerability          5.3 and earlier  All  Migrate to a fixed release.      6.0  All  Migrate to a fixed release.      6.1  All  Migrate to a fixed release.      6.2  6.2.1, 6.2.2  6.2.3      6.3  6.3.1  6.3.2, 6.3.3      6.4  Not vulnerable.  Not vulnerable.      6.5  6.5.2, 6.5.3  Migrate to a fixed release.      6.6  All  Migrate to a fixed release.      6.7  All  Fixed in 6.7.4 for ip sla responder configurations. ip sla responder twamp configurations are vulnerable; migrate to a fixed release.      7.0  All  Migrate to a fixed release.      7.1  All  Migrate to a fixed release.      7.2  All  7.2.2      7.3 and later  Not affected.  Not affected.\r\nCisco has released the following SMUs to address this vulnerability. Customers who require SMUs for platforms or releases that are not listed are advised to contact their support organization.\r\n\r\nThe SMUs in the following table address Cisco Bug ID CSCvw32825 [\"https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw32825\"] (for ip sla responder configurations).\r\n        Cisco IOS XR Software Release  Platform  SMU Name          6.3.3  ASR9K-PX  asr9k-px-6.3.3.CSCvw32825      6.4.2  ASR9K-X64  asr9k-x64-6.4.2.CSCvw32825      6.5.3  ASR9K-PX  asr9k-px-6.5.3.CSCvw32825      6.6.3  ASR9K-PX  asr9k-px-6.6.3.CSCvw32825      ASR9K-X64  asr9k-x64-6.6.3.CSCvw32825      NCS5500  ncs5500-6.6.3.CSCvw32825      6.7.3  ASR9K-PX  asr9k-px-6.7.3.CSCvw32825      7.1.2  NCS540  ncs540-7.1.2.CSCvw32825      NCS560  ncs560-7.1.2.CSCvw32825      NCS5500  ncs5500-7.1.2.CSCvw32825      7.1.3  ASR9K-X64  asr9k-x64-7.1.3.CSCvw32825\r\nThe SMUs in the following table address Cisco Bug ID CSCvw61840 [\"https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw61840\"] (for ip sla responder twamp configurations).\r\n        Cisco IOS XR Software Release  Platform  SMU Name          6.3.3  ASR9K-PX  asr9k-px-6.3.3.CSCvw61840      6.5.3  NCS5500  ncs5500-6.5.3.CSCvw61840      6.6.3  ASR9K-PX  asr9k-px-6.6.3.CSCvw61840      ASR9K-X64  asr9k-x64-6.6.3.CSCvw61840      7.1.3  ASR9K-X64  asr9k-x64-7.1.3.CSCvw61840\r\nThe Cisco Product Security Incident Response Team (PSIRT) validates only the affected and fixed release information that is documented in this advisory.",
        "title": "Fixed Software"
      },
      {
        "category": "general",
        "text": "To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy [\"https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html\"]. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.",
        "title": "Vulnerability Policy"
      },
      {
        "category": "general",
        "text": "The Cisco PSIRT is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.",
        "title": "Exploitation and Public Announcements"
      },
      {
        "category": "general",
        "text": "This vulnerability was found during the resolution of a Cisco TAC support case.",
        "title": "Source"
      },
      {
        "category": "legal_disclaimer",
        "text": "THIS DOCUMENT IS PROVIDED ON AN \"AS IS\" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.\r\n\r\nA standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.",
        "title": "Legal Disclaimer"
      }
    ],
    "publisher": {
      "category": "vendor",
      "contact_details": "psirt@cisco.com",
      "issuing_authority": "Cisco PSIRT",
      "name": "Cisco",
      "namespace": "https://wwww.cisco.com"
    },
    "references": [
      {
        "category": "self",
        "summary": "Cisco IOS XR Software IP Service Level Agreements  and Two-Way Active Measurement Protocol Denial of Service Vulnerability",
        "url": "https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-ipsla-ZA3SRrpP"
      },
      {
        "category": "external",
        "summary": "Cisco Event Response: September  2021 Semiannual Cisco IOS XR  Software Security Advisory Bundled Publication",
        "url": "https://sec.cloudapps.cisco.com/security/center/viewErp.x?alertId=ERP-74637"
      },
      {
        "category": "external",
        "summary": "Cisco Security Vulnerability Policy",
        "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html"
      },
      {
        "category": "external",
        "summary": "https://www.cisco.com/c/en/us/products/end-user-license-agreement.html",
        "url": "https://www.cisco.com/c/en/us/products/end-user-license-agreement.html"
      },
      {
        "category": "external",
        "summary": "considering software upgrades",
        "url": "https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html#fixes"
      },
      {
        "category": "external",
        "summary": "Cisco\u0026nbsp;Security Advisories page",
        "url": "https://www.cisco.com/go/psirt"
      },
      {
        "category": "external",
        "summary": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html",
        "url": "https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html"
      },
      {
        "category": "external",
        "summary": "CSCvw32825",
        "url": "https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw32825"
      },
      {
        "category": "external",
        "summary": "CSCvw61840",
        "url": "https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw61840"
      }
    ],
    "title": "Cisco IOS XR Software IP Service Level Agreements  and Two-Way Active Measurement Protocol Denial of Service Vulnerability",
    "tracking": {
      "current_release_date": "2021-10-08T12:49:15+00:00",
      "generator": {
        "date": "2024-05-10T23:07:49+00:00",
        "engine": {
          "name": "TVCE"
        }
      },
      "id": "cisco-sa-ipsla-ZA3SRrpP",
      "initial_release_date": "2021-09-08T16:00:00+00:00",
      "revision_history": [
        {
          "date": "2021-09-08T15:43:03+00:00",
          "number": "1.0.0",
          "summary": "Initial public release."
        },
        {
          "date": "2021-09-15T15:02:29+00:00",
          "number": "1.1.0",
          "summary": "Added additional SMUs."
        },
        {
          "date": "2021-10-08T12:49:15+00:00",
          "number": "1.2.0",
          "summary": "Added additional SMUs."
        }
      ],
      "status": "final",
      "version": "1.2.0"
    }
  },
  "product_tree": {
    "branches": [
      {
        "branches": [
          {
            "category": "product_family",
            "name": "Cisco IOS XR Software",
            "product": {
              "name": "Cisco IOS XR Software ",
              "product_id": "CSAFPID-5834"
            }
          }
        ],
        "category": "vendor",
        "name": "Cisco"
      }
    ]
  },
  "vulnerabilities": [
    {
      "cve": "CVE-2021-34720",
      "ids": [
        {
          "system_name": "Cisco Bug ID",
          "text": "CSCvw32825"
        },
        {
          "system_name": "Cisco Bug ID",
          "text": "CSCvw61840"
        }
      ],
      "notes": [
        {
          "category": "other",
          "text": "Complete.",
          "title": "Affected Product Comprehensiveness"
        }
      ],
      "product_status": {
        "known_affected": [
          "CSAFPID-5834"
        ]
      },
      "remediations": [
        {
          "category": "vendor_fix",
          "details": "Cisco has released software updates that address this vulnerability.",
          "product_ids": [
            "CSAFPID-5834"
          ],
          "url": "https://software.cisco.com"
        }
      ],
      "scores": [
        {
          "cvss_v3": {
            "baseScore": 8.6,
            "baseSeverity": "HIGH",
            "vectorString": "CVSS:3.1/AV:N/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:H",
            "version": "3.1"
          },
          "products": [
            "CSAFPID-5834"
          ]
        }
      ],
      "title": "Cisco IOS XR Software IP Service Level Agreements  and Two-Way Active Measurement Protocol Denial of Service Vulnerability"
    }
  ]
}


Log in or create an account to share your comment.




Tags
Taxonomy of the tags.


Loading...

Loading...

Loading...

Sightings

Author Source Type Date

Nomenclature

  • Seen: The vulnerability was mentioned, discussed, or seen somewhere by the user.
  • Confirmed: The vulnerability is confirmed from an analyst perspective.
  • Exploited: This vulnerability was exploited and seen by the user reporting the sighting.
  • Patched: This vulnerability was successfully patched by the user reporting the sighting.
  • Not exploited: This vulnerability was not exploited or seen by the user reporting the sighting.
  • Not confirmed: The user expresses doubt about the veracity of the vulnerability.
  • Not patched: This vulnerability was not successfully patched by the user reporting the sighting.