CVE-2026-15461 (GCVE-0-2026-15461)
Vulnerability from cvelistv5 – Published: 2026-09-10 14:34 – Updated: 2026-09-10 16:58
VLAI
EPSS
VEX
Title
Type confusion in Zephyr HL78xx GNSS NMEA driver causes wild-pointer write from GNSS input
Summary
The Sierra Wireless HL78xx modem GNSS driver (drivers/modem/hl78xx/, later drivers/modem/vendor_standalone/hl78xx/) embeds a generic struct gnss_nmea0183_match_data match_data inside struct hl78xx_gnss_data. The generic NMEA0183 match helper (drivers/gnss/gnss_nmea0183_match.c) requires that context to be the first member because its callbacks cast user_data directly to struct gnss_nmea0183_match_data . In the affected releases match_data was the second member (after const struct device dev), so it sat at a non-zero offset while gnss_nmea0183_match_init() initialized it at the correct address. The registered NMEA handlers instead pass the whole device data object (data->devices.gnss->data, offset 0), producing an offset-shifted type confusion between where state is initialized and where the parse callbacks read and write it.
When NMEA sentences from the GNSS receiver are parsed, the GGA/RMC callbacks write parsed fix data into the wrong location within the struct, and the GSV callback (gnss_nmea0183_match_gsv_callback, active under CONFIG_GNSS_SATELLITES) reads its satellites pointer and bound from the wrong offsets — non-pointer bytes of struct hl78xx_gnss_data — and then writes parsed struct gnss_satellite entries through that bogus pointer. This is a write through an uninitialized/wild pointer with a garbage bound.
The NMEA handlers are registered by default (CONFIG_HL78XX_GNSS_SOURCE_NMEA is the default GNSS source) on devices using the HL78xx GNSS. The driver runs in kernel context and the NMEA data originates from the GNSS radio front-end, so a party able to influence the GNSS signal (for example GNSS/GPS spoofing at radio proximity) can drive the kernel-side parser into the faulty write. The most likely impact is a crash (denial of service) because the bogus pointer resolves to a fixed near-NULL value, with adjacent-memory corruption possible on MMU-less targets. Confidentiality is not affected. Exploitation requires the satellites feature to be enabled and active, so attack complexity is high.
Severity
5.3 (Medium)
SSVC
Exploitation: none
Automatable: no
Technical Impact: partial
CISA Coordinator · CISA-ADP (v2.0.3)
Decision recorded 2026-09-10 16:57 UTC
CWE
- CWE-843 - memory-safety
Assigner
References
2 references
Impacted products
1 product
| Vendor | Product | Version | CPE status | |
|---|---|---|---|---|
| zephyrproject | zephyr |
Affected:
4.4.0 , < 4.4.2
(semver)
|
guessed |
{
"containers": {
"adp": [
{
"metrics": [
{
"other": {
"content": {
"id": "CVE-2026-15461",
"options": [
{
"Exploitation": "none"
},
{
"Automatable": "no"
},
{
"Technical Impact": "partial"
}
],
"role": "CISA Coordinator",
"timestamp": "2026-09-10T16:57:25.442788Z",
"version": "2.0.3"
},
"type": "ssvc"
}
}
],
"providerMetadata": {
"dateUpdated": "2026-09-10T16:58:19.058Z",
"orgId": "134c704f-9b21-4f2e-91b3-4a467353bcc0",
"shortName": "CISA-ADP"
},
"title": "CISA ADP Vulnrichment"
}
],
"cna": {
"affected": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"drivers/modem/vendor_standalone/hl78xx/hl78xx_gnss.h"
],
"programRoutines": [
{
"name": "hl78xx_get_gnss_data"
},
{
"name": "hl78xx_gnss_nmea0183_match_gga"
},
{
"name": "hl78xx_gnss_nmea0183_match_gsa"
},
{
"name": "hl78xx_gnss_nmea0183_match_gst"
},
{
"name": "hl78xx_gnss_nmea0183_match_gsv"
},
{
"name": "hl78xx_gnss_nmea0183_match_rmc"
},
{
"name": "hl78xx_gnss_nmea_match_epu"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThan": "4.4.2",
"status": "affected",
"version": "4.4.0",
"versionType": "semver"
}
]
}
],
"descriptions": [
{
"lang": "en",
"value": "The Sierra Wireless HL78xx modem GNSS driver (drivers/modem/hl78xx/, later drivers/modem/vendor_standalone/hl78xx/) embeds a generic struct gnss_nmea0183_match_data match_data inside struct hl78xx_gnss_data. The generic NMEA0183 match helper (drivers/gnss/gnss_nmea0183_match.c) requires that context to be the first member because its callbacks cast user_data directly to struct gnss_nmea0183_match_data . In the affected releases match_data was the second member (after const struct device dev), so it sat at a non-zero offset while gnss_nmea0183_match_init() initialized it at the correct address. The registered NMEA handlers instead pass the whole device data object (data-\u003edevices.gnss-\u003edata, offset 0), producing an offset-shifted type confusion between where state is initialized and where the parse callbacks read and write it.\n\nWhen NMEA sentences from the GNSS receiver are parsed, the GGA/RMC callbacks write parsed fix data into the wrong location within the struct, and the GSV callback (gnss_nmea0183_match_gsv_callback, active under CONFIG_GNSS_SATELLITES) reads its satellites pointer and bound from the wrong offsets \u2014 non-pointer bytes of struct hl78xx_gnss_data \u2014 and then writes parsed struct gnss_satellite entries through that bogus pointer. This is a write through an uninitialized/wild pointer with a garbage bound.\n\nThe NMEA handlers are registered by default (CONFIG_HL78XX_GNSS_SOURCE_NMEA is the default GNSS source) on devices using the HL78xx GNSS. The driver runs in kernel context and the NMEA data originates from the GNSS radio front-end, so a party able to influence the GNSS signal (for example GNSS/GPS spoofing at radio proximity) can drive the kernel-side parser into the faulty write. The most likely impact is a crash (denial of service) because the bogus pointer resolves to a fixed near-NULL value, with adjacent-memory corruption possible on MMU-less targets. Confidentiality is not affected. Exploitation requires the satellites feature to be enabled and active, so attack complexity is high."
}
],
"metrics": [
{
"cvssV3_1": {
"baseScore": 5.3,
"baseSeverity": "MEDIUM",
"vectorString": "CVSS:3.1/AV:A/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:H",
"version": "3.1"
},
"format": "CVSS"
}
],
"problemTypes": [
{
"descriptions": [
{
"cweId": "CWE-843",
"description": "memory-safety",
"lang": "en",
"type": "CWE"
}
]
}
],
"providerMetadata": {
"dateUpdated": "2026-09-10T14:34:21.914Z",
"orgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"shortName": "zephyr"
},
"references": [
{
"name": "Fix commit",
"tags": [
"patch"
],
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/8a2465784e8909aa3835559381a60c00cc2218a1"
},
{
"name": "GHSA-vvjg-6rg4-7235",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-vvjg-6rg4-7235"
}
],
"title": "Type confusion in Zephyr HL78xx GNSS NMEA driver causes wild-pointer write from GNSS input",
"x_generator": {
"engine": "cvelib 1.8.0"
}
}
},
"cveMetadata": {
"assignerOrgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"assignerShortName": "zephyr",
"cveId": "CVE-2026-15461",
"datePublished": "2026-09-10T14:34:21.914Z",
"dateReserved": "2026-07-10T20:12:01.873Z",
"dateUpdated": "2026-09-10T16:58:19.058Z",
"state": "PUBLISHED"
},
"dataType": "CVE_RECORD",
"dataVersion": "5.2",
"vulnerability-lookup:meta": {
"epss": {
"cve": "CVE-2026-15461",
"date": "2026-09-11",
"epss": "0.00158",
"percentile": "0.05331"
},
"nvd": "{\"cve\":{\"id\":\"CVE-2026-15461\",\"sourceIdentifier\":\"vulnerabilities@zephyrproject.org\",\"published\":\"2026-09-10T15:17:25.060\",\"lastModified\":\"2026-09-10T17:17:01.853\",\"vulnStatus\":\"Awaiting Analysis\",\"cveTags\":[],\"descriptions\":[{\"lang\":\"en\",\"value\":\"The Sierra Wireless HL78xx modem GNSS driver (drivers/modem/hl78xx/, later drivers/modem/vendor_standalone/hl78xx/) embeds a generic struct gnss_nmea0183_match_data match_data inside struct hl78xx_gnss_data. The generic NMEA0183 match helper (drivers/gnss/gnss_nmea0183_match.c) requires that context to be the first member because its callbacks cast user_data directly to struct gnss_nmea0183_match_data . In the affected releases match_data was the second member (after const struct device dev), so it sat at a non-zero offset while gnss_nmea0183_match_init() initialized it at the correct address. The registered NMEA handlers instead pass the whole device data object (data-\u003edevices.gnss-\u003edata, offset 0), producing an offset-shifted type confusion between where state is initialized and where the parse callbacks read and write it.\\n\\nWhen NMEA sentences from the GNSS receiver are parsed, the GGA/RMC callbacks write parsed fix data into the wrong location within the struct, and the GSV callback (gnss_nmea0183_match_gsv_callback, active under CONFIG_GNSS_SATELLITES) reads its satellites pointer and bound from the wrong offsets \u2014 non-pointer bytes of struct hl78xx_gnss_data \u2014 and then writes parsed struct gnss_satellite entries through that bogus pointer. This is a write through an uninitialized/wild pointer with a garbage bound.\\n\\nThe NMEA handlers are registered by default (CONFIG_HL78XX_GNSS_SOURCE_NMEA is the default GNSS source) on devices using the HL78xx GNSS. The driver runs in kernel context and the NMEA data originates from the GNSS radio front-end, so a party able to influence the GNSS signal (for example GNSS/GPS spoofing at radio proximity) can drive the kernel-side parser into the faulty write. The most likely impact is a crash (denial of service) because the bogus pointer resolves to a fixed near-NULL value, with adjacent-memory corruption possible on MMU-less targets. Confidentiality is not affected. Exploitation requires the satellites feature to be enabled and active, so attack complexity is high.\"}],\"affected\":[{\"source\":\"vulnerabilities@zephyrproject.org\",\"affectedData\":[{\"vendor\":\"zephyrproject\",\"product\":\"zephyr\",\"defaultStatus\":\"unaffected\",\"collectionURL\":\"https://github.com/zephyrproject-rtos/zephyr\",\"packageName\":\"zephyr\",\"programFiles\":[\"drivers/modem/vendor_standalone/hl78xx/hl78xx_gnss.h\"],\"programRoutines\":[{\"name\":\"hl78xx_get_gnss_data\"},{\"name\":\"hl78xx_gnss_nmea0183_match_gga\"},{\"name\":\"hl78xx_gnss_nmea0183_match_gsa\"},{\"name\":\"hl78xx_gnss_nmea0183_match_gst\"},{\"name\":\"hl78xx_gnss_nmea0183_match_gsv\"},{\"name\":\"hl78xx_gnss_nmea0183_match_rmc\"},{\"name\":\"hl78xx_gnss_nmea_match_epu\"}],\"versions\":[{\"version\":\"4.4.0\",\"lessThan\":\"4.4.2\",\"versionType\":\"semver\",\"status\":\"affected\"}]}]}],\"metrics\":{\"cvssMetricV31\":[{\"source\":\"vulnerabilities@zephyrproject.org\",\"type\":\"Secondary\",\"cvssData\":{\"version\":\"3.1\",\"vectorString\":\"CVSS:3.1/AV:A/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:H\",\"baseScore\":5.3,\"baseSeverity\":\"MEDIUM\",\"attackVector\":\"ADJACENT_NETWORK\",\"attackComplexity\":\"HIGH\",\"privilegesRequired\":\"NONE\",\"userInteraction\":\"NONE\",\"scope\":\"UNCHANGED\",\"confidentialityImpact\":\"NONE\",\"integrityImpact\":\"NONE\",\"availabilityImpact\":\"HIGH\"},\"exploitabilityScore\":1.6,\"impactScore\":3.6}],\"ssvcV203\":[{\"source\":\"134c704f-9b21-4f2e-91b3-4a467353bcc0\",\"ssvcData\":{\"timestamp\":\"2026-09-10T16:57:25.442788Z\",\"id\":\"CVE-2026-15461\",\"options\":[{\"exploitation\":\"none\"},{\"automatable\":\"no\"},{\"technicalImpact\":\"partial\"}],\"role\":\"CISA Coordinator\",\"version\":\"2.0.3\"}}]},\"weaknesses\":[{\"source\":\"vulnerabilities@zephyrproject.org\",\"type\":\"Secondary\",\"description\":[{\"lang\":\"en\",\"value\":\"CWE-843\"}]}],\"references\":[{\"url\":\"https://github.com/zephyrproject-rtos/zephyr/commit/8a2465784e8909aa3835559381a60c00cc2218a1\",\"source\":\"vulnerabilities@zephyrproject.org\"},{\"url\":\"https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-vvjg-6rg4-7235\",\"source\":\"vulnerabilities@zephyrproject.org\"}]}}",
"vulnrichment": {
"containers": "{\"adp\": [{\"title\": \"CISA ADP Vulnrichment\", \"metrics\": [{\"other\": {\"type\": \"ssvc\", \"content\": {\"id\": \"CVE-2026-15461\", \"role\": \"CISA Coordinator\", \"options\": [{\"Exploitation\": \"none\"}, {\"Automatable\": \"no\"}, {\"Technical Impact\": \"partial\"}], \"version\": \"2.0.3\", \"timestamp\": \"2026-09-10T16:57:25.442788Z\"}}}], \"providerMetadata\": {\"orgId\": \"134c704f-9b21-4f2e-91b3-4a467353bcc0\", \"shortName\": \"CISA-ADP\", \"dateUpdated\": \"2026-09-10T16:58:02.696Z\"}}], \"cna\": {\"title\": \"Type confusion in Zephyr HL78xx GNSS NMEA driver causes wild-pointer write from GNSS input\", \"metrics\": [{\"format\": \"CVSS\", \"cvssV3_1\": {\"version\": \"3.1\", \"baseScore\": 5.3, \"baseSeverity\": \"MEDIUM\", \"vectorString\": \"CVSS:3.1/AV:A/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:H\"}}], \"affected\": [{\"vendor\": \"zephyrproject\", \"product\": \"zephyr\", \"versions\": [{\"status\": \"affected\", \"version\": \"4.4.0\", \"lessThan\": \"4.4.2\", \"versionType\": \"semver\"}], \"packageName\": \"zephyr\", \"programFiles\": [\"drivers/modem/vendor_standalone/hl78xx/hl78xx_gnss.h\"], \"collectionURL\": \"https://github.com/zephyrproject-rtos/zephyr\", \"defaultStatus\": \"unaffected\", \"programRoutines\": [{\"name\": \"hl78xx_get_gnss_data\"}, {\"name\": \"hl78xx_gnss_nmea0183_match_gga\"}, {\"name\": \"hl78xx_gnss_nmea0183_match_gsa\"}, {\"name\": \"hl78xx_gnss_nmea0183_match_gst\"}, {\"name\": \"hl78xx_gnss_nmea0183_match_gsv\"}, {\"name\": \"hl78xx_gnss_nmea0183_match_rmc\"}, {\"name\": \"hl78xx_gnss_nmea_match_epu\"}]}], \"references\": [{\"url\": \"https://github.com/zephyrproject-rtos/zephyr/commit/8a2465784e8909aa3835559381a60c00cc2218a1\", \"name\": \"Fix commit\", \"tags\": [\"patch\"]}, {\"url\": \"https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-vvjg-6rg4-7235\", \"name\": \"GHSA-vvjg-6rg4-7235\"}], \"x_generator\": {\"engine\": \"cvelib 1.8.0\"}, \"descriptions\": [{\"lang\": \"en\", \"value\": \"The Sierra Wireless HL78xx modem GNSS driver (drivers/modem/hl78xx/, later drivers/modem/vendor_standalone/hl78xx/) embeds a generic struct gnss_nmea0183_match_data match_data inside struct hl78xx_gnss_data. The generic NMEA0183 match helper (drivers/gnss/gnss_nmea0183_match.c) requires that context to be the first member because its callbacks cast user_data directly to struct gnss_nmea0183_match_data . In the affected releases match_data was the second member (after const struct device dev), so it sat at a non-zero offset while gnss_nmea0183_match_init() initialized it at the correct address. The registered NMEA handlers instead pass the whole device data object (data-\u003edevices.gnss-\u003edata, offset 0), producing an offset-shifted type confusion between where state is initialized and where the parse callbacks read and write it.\\n\\nWhen NMEA sentences from the GNSS receiver are parsed, the GGA/RMC callbacks write parsed fix data into the wrong location within the struct, and the GSV callback (gnss_nmea0183_match_gsv_callback, active under CONFIG_GNSS_SATELLITES) reads its satellites pointer and bound from the wrong offsets \\u2014 non-pointer bytes of struct hl78xx_gnss_data \\u2014 and then writes parsed struct gnss_satellite entries through that bogus pointer. This is a write through an uninitialized/wild pointer with a garbage bound.\\n\\nThe NMEA handlers are registered by default (CONFIG_HL78XX_GNSS_SOURCE_NMEA is the default GNSS source) on devices using the HL78xx GNSS. The driver runs in kernel context and the NMEA data originates from the GNSS radio front-end, so a party able to influence the GNSS signal (for example GNSS/GPS spoofing at radio proximity) can drive the kernel-side parser into the faulty write. The most likely impact is a crash (denial of service) because the bogus pointer resolves to a fixed near-NULL value, with adjacent-memory corruption possible on MMU-less targets. Confidentiality is not affected. Exploitation requires the satellites feature to be enabled and active, so attack complexity is high.\"}], \"problemTypes\": [{\"descriptions\": [{\"lang\": \"en\", \"type\": \"CWE\", \"cweId\": \"CWE-843\", \"description\": \"memory-safety\"}]}], \"providerMetadata\": {\"orgId\": \"e2e69745-5e70-4e92-8431-deb5529a81ad\", \"shortName\": \"zephyr\", \"dateUpdated\": \"2026-09-10T14:34:21.914Z\"}}}",
"cveMetadata": "{\"cveId\": \"CVE-2026-15461\", \"state\": \"PUBLISHED\", \"dateUpdated\": \"2026-09-10T16:58:19.058Z\", \"dateReserved\": \"2026-07-10T20:12:01.873Z\", \"assignerOrgId\": \"e2e69745-5e70-4e92-8431-deb5529a81ad\", \"datePublished\": \"2026-09-10T14:34:21.914Z\", \"assignerShortName\": \"zephyr\"}",
"dataType": "CVE_RECORD",
"dataVersion": "5.2"
}
}
}
Loading…
Loading…
Experimental. This forecast is provided for visualization only and may change without notice. Do not use it for operational decisions.
Forecast uses a logistic model when the trend is rising, or an exponential decay model when the trend is falling. Fitted via linearized least squares.
Sightings
| Author | Source | Type | Date | Other |
|---|
Nomenclature
- Seen: The vulnerability was mentioned, discussed, or observed by the user.
- Confirmed: The vulnerability has been validated from an analyst's perspective.
- Published Proof of Concept: A public proof of concept is available for this vulnerability.
- Exploited: The vulnerability was observed as exploited by the user who reported the sighting.
- Patched: The vulnerability was observed as successfully patched by the user who reported the sighting.
- Not exploited: The vulnerability was not observed as exploited by the user who reported the sighting.
- Not confirmed: The user expressed doubt about the validity of the vulnerability.
- Not patched: The vulnerability was not observed as successfully patched by the user who reported the sighting.
Loading…
The MITRE ATT&CK techniques below are AI-generated suggestions, inferred from the description of the
vulnerability by the CIRCL/vulnerability-attack-technique-classification-roberta-base
model, served locally by ML-Gateway.
They have not been verified by an analyst and are provided for guidance only.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Loading…
Loading…